|
Inputs 1 - 3
- Inputs 1 is set as Microphone
Input Impedance is 250
ohm balanced. Input 2-4 can
be set as MIC Inputs or switched to
AUX 1 and AUX 2 respectively
(internal switch). Impedance is 47 K
ohm.
Phantom Power
- Phantom Power is provided on
all Inputs set as
Microphone.
Stereo Summing
- Two separate RCA Jacks are
provided
for Input 3 and 4 (Left and
Right). A Stereo signal connected
to either Input is buffered
and internally summed to
Mono.
Input 3 & 4 Attenuators
- When the Inputs are set as
AUX 1 and
AUX 2 the input sensitivity
may be varied by a rear panel Variable
Attenuator. This feature
allows to set the output level of Programs
originating from different
sources (CD, Satellite Receiver, etc.).
Phone Paging
- A separate input is provided
to interface with a
Phone System. Input Impedance
is 600 ohm, Transformer
Balanced. A level control is
available on the front panel.
Module Port
- Por t accepts standard
plug-in module.
Module Level Control is
provided on the front panel. See list
of modules available from
PASO.
MIX BUSS
- This Input/Output may be
utilized to parallel two
amplifiers or as an input for
a Microphone Mixer or other
audio source. When used as an
Input the Amplifier Level and
Equalization Controls have no
effect.
Line Out
- 600 ohm, 1.5 Volt Line
Output.
Remote Volume Control
- The AUX 1 Input Volume may
be adjusted from a remote
location. The Remote Volume
Input utilizes a 10K Pot and
is immune to Audio Interference
(DC Operation).
Addressable Dual VOX System
- The Dual VOX System can
be individually selected to
operate independently on all
Inputs by means of jumpers .
Any Input may be set to activate
either VOX 1 or VOX 2.
Addressable Dual Muting
System
- The Dual VOX System
can be individually selected
to operate independently with
all Inputs by means of
jumpers . Any Input may be set to
activate either MUTE 1 or
MUTE 2.
MUTE 2 Adjustable Delay
- A rear panel control adjusts
the
MUTE 2 Time Delay (the time
the MUTE 2 stays activated)
from 3 Sec. to 60 Sec.
Particularly useful to control the
length of time that an Input
mutes another (for example AUX
1 over AUX 2).
Music on Hold - Output
Channel 1
- Channel 1 provides a
1 Volt, 600 ohm balanced
output and a 2 Watt, 8 ohm output
for Music/Message on Hold or
Zone 1 Speaker Output.
Internal Jumper selects the
source from either AUX 1, AUX
2 or Input Module. Level
Control is provided.
Output Channel 2
- Channel 2 provides a 2 Watt,
8 ohm
output for Zone 2 Speaker
Output. Internal Jumper selects
the source from either AUX 1,
AUX 2 or Input Module. Level
Control is provided.
EQ LINK
- EQ Link (Preamp Out) (Power
Amp In) jacks are
provided for External
Equalizer. Activated by the EQ Link
Switch.
Tone By-Pass Switch
- The Tone by-pass switch
defeats
the setting of the Treble and
Bass Controls. Should be used
when an External Equalizer is
utilized.
24 VDC Supply Output
- A 24 Volt DC, 250 mA
regulated
Power Supply is provided for
external accessories
UL 6500 Listed (US - CANADA)
~top~ |
